Copperfield Chimney Cap Installation Nationwide

Copperfield Chimney Cap Installation: The Flushing Owner’s Guide

We stock and install Copperfield-compatible chimney caps across Flushing, with most replacements running $340-$680 installed depending on flue size and whether your crown needs resealing underneath. For standard single-flue models in the 8″×13″ to 13″×13″ range, we usually have the match on the truck and can complete the job in one visit. Homeowners in Flushing typically call us after spotting rust streaks down the brick or finding debris, squirrels, or water in the firebox after a hard rain.

Call (516) 206-6672

Which Copperfield Models This Applies To

Copperfield chimney caps fall into several product families, and getting the right match matters more than you’d think. The Black Galvanized Single-Flue series covers most Flushing homes built between 1940 and 1980, with sizes stamped on the underside lip: 8″×8″, 8″×13″, 13″×13″, and the less common 13″×17″ for larger fireplace flues. The Stainless Steel Multi-Flue line, recognizable by its flat lid and corner-mount legs, requires exact outside-dimension measurements of your chimney crown, not the flue opening. We’ve seen owners in the Kissena Park area order the wrong multi-flue cap because they measured the flue instead of the crown overhang.

The Copperfield Wind-Resistant models with the internal baffle, popular after Hurricane Sandy retrofits, use a different leg spacing than the standard line. If your existing cap has a small “WR” stamp near the mesh screen, that’s your tell.

We carry both OEM Copperfield caps and equivalent-grade caps from Gelco and Olympia Chimney that meet the same 24-gauge galvanized or 304 stainless spec. For coastal-weather Flushing, where salt air accelerates rust at the base of Murray Hill and Willets Point, we typically recommend stepping up to stainless even if your original was galvanized. The part costs more. It also lasts.

Hearthstone Chimney Co. is an independent service provider. We are not affiliated with Copperfield.

Signs Your Copperfield Chimney Cap Installation Is Failing

• Rust-colored streaks on the brickwork below the cap. Galvanized steel caps in Flushing’s wet freeze-thaw cycles typically show surface rust at the leg welds first. Once water wicks through, it stains the crown and runs down the face. The cap is no longer protecting; it’s funneling water inward.
• Mesh screen pulled away or sagging. This is squirrel damage, usually, or raccoon leverage. A compromised screen means embers can escape and animals can enter. In the older homes near Flushing Cemetery, we’ve found nests built against dampers that haven’t opened in years.
• Cap sitting crooked or one leg detached. High wind, ice loading, or a poor original install. A tilted cap channels rainwater directly into the flue instead of shedding it. We’ve seen this after every March nor’easter.
• Water in the firebox or white efflorescence on interior firebrick. By the time you see this, the cap has been leaking long enough to damage the smoke shelf. The cap was your first line of defense. Now you need the cap plus an inspection of what’s below.
• Visible gaps between cap base and flue tile. Thermal expansion and the settling common in Flushing’s 1920s frame houses can open a gap. Draft pulls cold air down; heated air escapes up. Your heating bill climbs before you notice the cap.

Replacement Cost & What’s Included

What drives the range: flue size, whether we need to fabricate a custom leg extension for an oversized flue, and the condition of the crown beneath the old cap. We check that crown before we quote. No surprises on the bill. Our 90-Day Done Right Promise covers the installation and the seal. In writing, no arguing.

DIY or Call Us?

Here’s what you can safely check yourself: the size stamp on your existing Copperfield cap, whether all four legs are still seated, and whether the mesh is intact. Use binoculars from the ground. Do not climb.

Here’s where DIY goes wrong: chimney cap installation requires working at height on a surface that is often pitched, always unforgiving, and frequently slick with moss or ice. The cap must be level, legs tensioned evenly, and the flue-to-cap joint sealed with high-temp silicone rated to 500°F. A cap that looks straight from the ground can channel water for months before the stain shows inside. We’ve reinstalled three homeowner attempts in Flushing this year alone. Two had the wrong size. One was secured with deck screws that rusted through in eighteen months.

Our technicians carry Copperfield, Gelco, and Olympia Chimney caps on the truck. Most jobs finish in a single visit. Call (516) 206-6672 for a free estimate.

FAQs